|
E.F.I. Wiring
Kits for EJ-EH.
For information click here
|
| LOOMEFI-01 | Engine Management loom to suit Holden Series 1 & 2 V6 Commodore Engines | $550 c/o | |
|
| LOOMEFI-08 | Engine Management loom to suit Holden V6 Ecotec Engines | $700 c/o | |
|
| LOOMEFI-03 | Engine Management loom to suit Holden VN-VP V8 Engines | $550 c/o | |
|
| LOOMEFI-04 | Engine Management loom to suit Holden VR-VS V8 Engines | $700 c/o | |
|
| LOOMEFI-15 | Engine Management loom to suit Holden VT V8 Manual & Auto Engines | $700 c/o | |
|
| MEMCAL-VT/V8 | Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. | $450c/o | |
|
| MEMCAL-VT/V6 | Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. | $450c/o | |
|
| MEMCAL-VR/V6 Man | Re-Programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit Conversion. | $450c/o | |
|
| MEMCAL-VR/V6 AUTO | Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. | $450c/o | |
|
| LOOMS/S-01 | Speed Sensor assembly & Loom with speedo cable provision. Suit T-700 Auto Trans. | $250 | |
|
| LOOMS/S-02 | Speed Sensor assembly & Loom with speedo cable provision. Suit T-350-400. Powerglide Auto Trans. | $200 | |
|
|
| B0580464070 | Hi-pressure EFI fuel pump | $195 | |  |
|
| BF-5030 | Hi-pressure fuel filter | $20 | | |
|
| 11004/KIT | Lift pump. Low pressure | $140 | | |
|
| ST-4 | EFI Surge Tank | $235 | | |
|
| GENIII-WELD RING/MS | EFI Fuel Pump Weld Ring. Holds in-tank fuel pump in place on tank. Suit Mild Steel Tank | $132 | | |
|
| 10229 | EFI Fuel Pump. Includes swirl pot. In-tank application to be used with GENIII-WELD RING | $350 | |
|
| FAN-VTCOMM | VT COMMODORE TWIN THERMO FAN ASSEMBLY. FACTORY REPLACEMENT UNIT. IDEAL FOR ENGINE CONVERSIONS | $270 | |
|
| FAN-EF4026 | 16'' 2100cfm UNIVERSAL FAN | $210 | |
|
| SUMP-04B | V6 Reversed Sump including Pickup | 550 c/o | |
|
| Error - No Match for SUMP-04A |
| CH-EM60 | COMMODORE V6 ENGINE INTO HOLDEN FJ TO EH | $200 | |
|
| Error - No Match for XM-01 |
| A1158 | Transmission rubber mount to suit T350-T400-T700-Powerglide and T5 | $44 | | |
|
| CH-59A | HOLDEN EJ-EH WITH 3.8 EFI COMMODORE V6. NON-ECOTEC 3 INTO1 DESIGN 1 5/8'' PRIM. MUST USE ENGINE MOUNTS EM-60 | $660 | | |
|
| | HEADERS TO SUIT V8 CHEV or V8 HOLDEN CONVERSIONS | POA | |
|
| SPEEDO-01 | Electronic Speedometer conversion. | $550 | |
|
| W/M-HOLDEN EJ-EH | HOLDEN EJ-EH | $295 | | |
|
| G/R-3/1.9 | 253-308 V8 Holden. Suit Manual & Automatic trans. 1.9HP / 1.4KW | $350 | | |
|
| G/R-3/2.5 | 253-308 V8 Holden. Suit Manual & Automatic trans. 2.5HP | $410 | | |
|
| G/R-3/6C1.9 | 6 Cylinder Holden. 1.9HP / 1.4KW | $355 | | |
|
| G/R-3/6C2.5 | 6 Cylinder Holden. 2.5HP | $440 | | |
|
| G/R-3/V6A | V6 3.8ltr Commodore Engine. Standard Replacement suit Auto | $180 | | |
|
| G/R-3/V6M1.9 | V6 3.8ltr Commodore Engine. Suit Manual trans. (10 Tooth pinion) | $350 | | |
|
|
E.F.I.
Wiring Kits for EJ-EH Holden fitted with Series 1, Series 2 or Ecotech Holden 3.8 Litre V6
or V8 EFI Engine and Transmission.
Fitting Details; We recommend that this conversion, whether it be a V6 or V8 engine that is to be fitted,
should be done with the Castlemaine Rod Shop
under body bracing kit, which bolts under the car and incorporates the gearbox crossmember to
which the handbrake mechanism is attached and a tailshaft safety loop for safety sake.
Only a very minor welding job is required
where the rail locks into the rear spring hangers, the rest is all bolt in with only holes
to be drilled by the fitter. The frame then allows the vehicle to be easily
jacked up, lifted on a hoist and of course prevents body deterioration
(fatigue). A raised floor tunnel is supplied and can be screwed, welded or pop
riveted in.
The installation is carried out with the
use of a HD-HR front crossmember. The front outrigger is removed and replaced with one
from an EJ-EH, if available, or custom built to suit. The crossmember centre section is
cut out for sump clearance and strengthened considerably. A strengthening
plate is added to the bottom to make the underneath look smooth. A rack and pinion
steering unit is fitted to the front of the crossmember.
The best approach is to purchase a HD-HR
drum brake front end (disc brake units are very hard to find), strip the front end and use
the crossmember as a change over unit to cut costs. The existing suspension components
should be reconditioned with new bushings and ball joints as necessary then re-fitted to
the new crossmember. A disc brake conversion kit (DB 8) is available from the Castlemaine Rod Shop to fit HQ-WB
ventilated discs to the drum brake spindles and is essential.
The rack and pinion kit consists of
approximately 34 pieces including reshaped steering arms, wishbone strengthening rods,
stabiliser brackets and bar connectors, all mounting rubbers, a length of 9/16"
steering bar, bushes, bolts etc. No universals are supplied as these are standard Torana
units. The steering column used is up to the fitter, however CRS can supply a modified
EJ-HR unit along with a specially made extension to clear the exhausts. If in Queensland,
this column is part of the requirements and a specially made floor mounting bracket must
be used. This is not essential in any other state of Australia (or N.Z.), where you can
fit whichever column you wish. An LH Torana unit is a good one to look for.
Extractors are required for V6 & V8
conversions, with provision for screw in oxygen sensor. It is also recommended that
they be JET-HOT Coated, which we can also
supply. This process stops heat dissipating through the pipes, stops corrosion and looks
great as well as giving your extractors a life time guarantee.
If using a post 1994 engine please note
that the matching transmission has no provision for a mechanical speedo cable. We
recommend that you use a pre 1994 transmission if you wish to retain the original speedo.
If using the post 1994 transmission a matching digital speedo is required and will need to
be custom adapted into the dash.
We have found it best to set up the battery
on the right hand side and the air box fitted to the left hand side. The E.C.M. is mounted
back in the original position (LHS kick panel) or above the glove box. Our wiring loom is
supplied on a changeover basis for the engine to computer loom. If no changeover is
supplied an additional cost of $200 will apply. Prices may vary if Ecotech engine is
used.
|
All Prices in $Au
including GST. Overseas orders will be lower.
Back to the EFI wiring page
 -
|
)
)
)
)
)
)
)
)
)
)
)
)
)
'))